Measurement Of Mechanical Properties Research Articles

Mechanical property measurement at high temperature based on a new disc-shaped specimen

Three-dimensional digital image correlation (3D-DIC) is frequently used to measure mechanical properties of materials. However, the traditional dumbbell-shapedspecimen has some limitations for measurment of mechanical properties of materials by use of 3D-DIC at high temperature due to two reasons: (1) its transverse dimension is very small and only a small number of valid speckles can be used in 3D-DIC; and (2) only a small amount of valid information, such as the average deformation of the gauge length, can be used to obtain mechanical properties in one direction. In this work, a new test method based on a disc-shaped standard specimen is first proposed. By use of analytical solutions of a disc under a uniform radial load, and measured results of the full-field displacement of the disc-shaped specimen by 3D-DIC in an effective test region at different high temperatures, mechanical properties at different high temperatures are identified.

Effect of annealing temperature on the evolution of microstructure, texture, and mechanical properties of hot-rolled 12Cr-ODS steel

To achieve high thermal efficiency, today's nuclear reactor structures are exposed to higher temperatures and pressures, which requires the use of high-strength steels with specific properties, such as ODS steels. There is a need to clarify the evolution of the microstructure and properties of steels at elevated temperatures. This study systematically investigates the evolution of microstructure, texture, and mechanical property variations of 12Cr-ODS steels after hot-rolling and subsequent annealing at 1000 °C and 1200 °C. The investigation utilizes optical microscopy, electron backscatter diffraction technique, and mechanical property measurements. The microstructure of hot-rolled samples shows a layered alternating distribution, which is distinguished by a notable presence of the α-fiber texture. Following annealing at 1000 °C, the martensite grains are smaller with a reduced hardness, while maintaining a strong α-fiber texture. After annealing at 1200 °C, there is a rapid increase in the growth of martensite grains, a significant rise in hardness, a reduction in the α-fiber texture characteristics, and an improvement in the γ-fiber texture characteristics. Moreover, the maximum intensity of the α-fiber texture diminishes as the annealing temperature increases. The mechanical properties of the samples deteriorated after annealing at 1200 °C, which can be attributed to the coarse martensite grains and the texture components containing the {001} cleavage plane dominating the occurrence of brittle cleavage fracture. The 0.1Y sample after annealing at 1000 °C exhibits an excellent combination of strength (1458 MPa) and ductility (20.3%), which is owing to the unique heterogeneous grain structure and the evolution of favorable texture.

A novel impact indentation technique with dynamic calibration method for measurement of dynamic mechanical properties

High strain rates and continuous real-time data acquisition are difficult to balance in existing impact indentation techniques. Meanwhile, the inaccuracy of the testing P-h curves limits the development of quantitative applications for dynamic testing of mechanical properties at micro region. This article develops a momentum exchange impact indentation testing method, which extends the testing range of strain rate to above 105 s−1, and at the same time avoids secondary impact. Impact indentation tests are conducted on single-crystal aluminum specimens with impact velocity from 76.9 to 176 mm/s. Based on calibrated data, the comparison of calculation methods for dynamic hardness is carried out. The dynamic elastic modulus is obtained by means of the Oliver-Pharr method, which increases from 71.9 to 89.4 GPa with increasing impact velocity. A multi-dimensional data analysis method is proposed based on the obtained experimental data to quantitatively study the damping and stiffness characteristics of materials. This testing method is particularly useful for quantitatively obtaining the micro region dynamic mechanical properties of solid materials at high strain rates.

Curcumin mitigates Aβ33-42 fibril-induced neuronal injury in the hippocampus

The targeted removal of Aβ33-42 accumulation in vivo emerges as a promising strategy for Alzheimer's disease (AD) treatment, offering potential avenues for the development of innovative anti-AD therapeutics. In this study, the effect of curcumin (Cur) with AD therapeutic potential on the cellular mechanical properties of Aβ33-42 fibril-induced neurons injury in the hippocampus of mice has been explored. The results showed that Cur had no obvious toxicity and side effects on neuronal cells and could significantly inhibit Aβ33-42-induced cell damage and improve cell survival. The measurements of cell mechanical properties revealed that Cur could restore the mechanical properties of damaged cells to a large extent. In addition, the inhibition mechanism of Cur on Aβ33-42-induced damage cell model was explained, which provides clues for the development of new drugs for the AD treatment.

Tectonic fractures induced by strike-slip faulting in intracratonic ultradeep carbonate rocks: Insights from the finite element method and self-adaptive constraints computational model for boundary conditions

Numerical simulations of the paleostress field during a period of tectonic fracture formation and rock failure criteria are used to quantitatively predict the development and occurrence of tectonic fractures induced by the formation of the SB18 fault zone in the Middle Ordovician Yijianfang Formation of the Shunnan area, Tarim Basin, China. The results of acoustic emission experiments, mechanical property measurements, and tectonic fracture occurrence observations obtained from core descriptions and fullbore formation microimager logs are combined with the Andersonian model of faulting and the finite element method, which is widely used for the numerical simulation of stress fields, to investigate the paleotectonic and in situ stress fields via numerical simulation. The quantitative prediction of the opening pressure and opening sequence of tectonic fractures is based on the occurrence of tectonic fracture, numerical simulation of in situ stresses, and coordinate system conversion. The results show that the width of the fracture zone induced by strike-slip faulting is ∼310 m. The degree of fracture development is significantly increased when the Young’s modulus, paleostress difference, and paleostress difference coefficient of the rock are elevated. The current horizontal principal stress is positively correlated with the distance from the fault, and the elevated areal density of the secondary faults causes a clockwise deflection of the horizontal stress direction. SSE-striking shear fractures with orientations ranging from 140° to 150° and two sets of tensional fractures with orientations ranging from −40° to −35° and 55° to 60° are preferentially opened in the water injection development stage of the reservoir. As the horizontal stress difference, horizontal stress difference coefficient, and angle between the maximum horizontal principal stress and a fracture decrease, the fracture opening pressure decreases. At the structural highs (burial depths <6225 m) and lows (burial depths >6225 m), the fracture burial depth is positively and negatively correlated with the opening pressure, respectively. Quantitative prediction of tectonic fracture developmental characteristics, opening pressure, and the opening sequence and investigation of the main factors that control their development can help to identify and support opportunities for hydrocarbon exploration and development of fractured carbonate reservoirs.

Mechanical Tester Driven by Surface Tension.

The measurement of in-plane mechanical properties, such as Young's modulus and strength, of thin and stretchable materials has long been a challenge. Existing measurements, including wrinkle instability and nano indentation, are either indirect or destructive, and are inapplicable to meshes or porous materials, while the conventional tension test fails to measure the mechanical properties of nanoscale films. Here, we report a technique to test thin and stretchable films by loading a thin film afloat via differential surface tension and recording its deformation. We have demonstrated the method by measuring the Young's moduli of homogeneous films of soft materials including polydimethylsiloxane and Ecoflex and verified the results with known values. We further measured the strain distributions of meshes, both isotropic and anisotropic, which were otherwise nearly impossible to measure. The method proposed herein is expected to be generally applicable to many material systems that are thin, stretchable, and water-insoluble.

Assessment of Cementitious Composites for High-Temperature Geothermal Wells.

High-temperature (HT) geothermal wells can provide green power 24 hours a day, 7 days a week. Under harsh environmental and operational conditions, the long-term durability requirements of such wells require special cementitious composites for well construction. This paper reports a comprehensive assessment of geothermal cement composites in cyclic pressure function laboratory tests and field exposures in an HT geothermal well (300-350 °C), as well as a numerical model to complement the experimental results. Performances of calcium-aluminate cement (CAC)-based composites and calcium-free cement were compared against the reference ordinary Portland cement (OPC)/silica blend. The stability and degradation of the tested materials were characterized by crystalline composition, thermo-gravimetric and elemental analyses, morphological studies, water-fillable porosity, and mechanical property measurements. All CAC-based formulations outperformed the reference blend both in the function and exposure tests. The reference OPC/silica lost its mechanical properties during the 9-month well exposure through extensive HT carbonation, while the properties of the CAC-based blends improved over that period. The Modified Cam-Clay (MCC) plasticity parameters of several HT cement formulations were extracted from triaxial and Brazilian tests and verified against the experimental results of function cyclic tests. These parameters can be used in well integrity models to predict the field-scale behavior of the cement sheath under geothermal well conditions.

Depositional environmental controls on mechanical stratigraphy of Barakar Shales in Rajmahal Basin, India

Understanding mechanical behaviour of shale is essential for efficient shale gas extraction, which can vary in different depositional settings. The impact of sedimentary environment on shale characteristics, such as mineralogical composition, total organic carbon content (TOC), and petrophysical properties, has been extensively researched. However, its influence on shale mechanical properties, especially in defining mechanical stratigraphy for targeting specific fracturing intervals, remains less explored. In this study, the influence of depositional environment on the mechanical properties of shale samples from the Rajmahal Basin is evaluated. Tensile strength of the samples was measured by the Brazilian splitting tensile strength and the brittleness index was calculated as a measure of mechanical properties. In addition, inductively coupled plasma optical emission spectroscopy (ICP-OES), X-ray fluorescence spectroscopy (XRF), Rock-Eval 6, and X-ray diffraction (XRD) analysis were carried out to assess geochemical characteristics of the samples from different perspectives. The results revealed that such geochemical variations that are generally controlled by the depositional environment, would impact the mechanical properties of the samples. Based on major and trace elements proxies, the depositional environment was determined to be passive continental margin, with hot and humid paleoclimatic conditions and freshwater anoxic settings. Tensile strength and brittleness index of the shale samples was observed to vary between 0.93 and 4.12 MPa and 0.71 to 3.40, respectively, while samples with the TOC exceeding 15 wt% had a strong negative correlation with tensile strength, as reasonably expected, due to weakening impact of the sedimentary organic matter on the shale matrix. Tensile strength and brittleness index correlated positively with clay mineral content, particularly their type, but negatively with the quartz content. Furthermore, samples abundant in biogenic silica exhibited reduced brittleness compared to those with lithogenic silica. Nevertheless, the variation in mechanical properties with burial depth was not substantial, and the examination of stress-strain curves indicated an overall brittle nature of the layer where the samples were retrieved from. Overall, achieving more robust conclusions regarding mechanical stratigraphy within the studied section of the Rajmahal Basin, would necessitate additional vertical sampling.

Biosafety and chemical solubility studies of multiscale crystal-reinforced lithium disilicate glass-ceramics.

Lithium disilicate (Li2 Si2 O5 ) glass-ceramics are currently a more widely used all-ceramic restorative material due to their good mechanical properties and excellent aesthetic properties. However, they have a series of problems such as high brittleness and low fracture toughness, which has become the main bottleneck restricting its development. Therefore, in order to compensate for these shortcomings, we propose to prepare a reinforced glass-ceramics with better mechanical properties and to test the biosafety and chemical solubility of the material. Li2 Si2 O5 whiskers were synthesized by a one-step hydrothermal method, and multi-scale crystal-enhanced Li2 Si2 O5 glass-ceramics were prepared by reaction sintering. The biosafety of multi-scale crystal-reinforced Li2 Si2 O5 glass-ceramics was investigated by in vitro cytotoxicity test, rabbit pyrogen test, mice bone marrow micronucleus test, skin sensitization test, sub-chronic systemic toxicity test, and chronic systemic toxicity test. Additionally, the chemical solubility of multi-scale crystal-reinforced Li2 Si2 O5 glass-ceramics was investigated. The test results showed that the material was non-cytotoxic, non-thermogenic, non-mutagenic, non-sensitizing, and non-systemic. The chemical solubility, determined to be 377 ± 245 μg/cm2 , complied with the ISO 6872 standard for the maximum solubility of ceramic materials. Multi-scale crystal-reinforced Li2 Si2 O5 glass-ceramics' biosafety and chemical solubility met current normative criteria, and they can move on to mechanical property measurements (such as flexural strength test, fatigue life test, friction and wear property study, etc.) and bonding property optimization, which shows promise for future clinical applications.

Effect of Mn substitution on Cr in the Al-Cu-Er-Mg-Zr-Fe-Si-Ti cast alloy

The microstructure, phase composition, precipitates evaluation, casting, and mechanical properties of the novel cast Al-4Cu-2.1Er-1Mg-0.2Zr-0.2Cr-0.15Fe-0.15Si-0.1Ti alloy were analyzed using by optical microscope, scanning and transmission electron microscopes, differential scanning calorimetry, thermodynamic calculations, hot cracking and mechanical properties measurements. The positive effect of Cr as a substitution of Mn on plasticity and precipitation strengthening was demonstrated. The 0.2Zr, 0.2Cr and 0.1 Ti as a grain refiners provide a fine grain size of 25 μm in the as-cast state due to primary Al75–80Cu10–12Er3–4Cr7 phase particles formation as a nucleation centers of Al. The hot cracking index (HCI) of the AlCuErMgCr alloy was 12–14 mm which is similar with HCI of the cast Al-Si-Cu-Mg alloys. The good casting properties in the AlCuErMgCr alloy achieved due to a fine grain structure and narrow solidification range. The contribution of the Al3(Zr,Er) (40 nm), Al45Cr7 (6 nm), and S’(θ’) (100/5 nm) precipitates is 38.5 MPa, 140.4 MPa, and 198.9 MPa and the calculated contribution from dislocation and precipitates is 262.3 MPa. The ultimate tensile strength (UTS) and elongation (El.) of the AlCuErMgCr alloy are 372 MPa and 6% which is higher in 16.6% and 150%, respectively, than in the Mn-containing alloy. Novel alloy has an excellent combination of yield strength (YS) and plasticity at 20–250°C. The YS and El. are 301 MPa and 6% and 225–250 MPa and 4.6–11.5% at 20 and 200–250°C, respectively. The rupture strength at 250°C after 100 h (σ100250) is 106 MPa. Mechanical and casting properties of the novel alloy are superior to the properties of commercial 201.0 (Al-Cu-Mn-Mg-Ag-Ti) alloy.

Direct measurement of the effective properties of an additively manufactured titanium octet truss unit cell using high energy X-ray diffraction

Additively manufactured lattice structures offer a high specific strength-to-density ratio in comparison to conventional, fully dense parts. The small feature size and intricate geometry of lattice structures make it challenging to directly characterize their mechanical properties. This study presents direct measurement of the elastic mechanical properties of an additively manufactured titanium alloy octet truss unit cell. Strut stress and strain were measured using high-energy X-ray diffraction during quasi-static compressive loading. The crystallographic stress-strain relationship was converted into the stress-strain relationship of the octet truss lattice unit cell using the known symmetry of the struts. The sample studied herein was best fit by an orthorhombic linear elastic stress-strain relationship. This technique shows promise for studying additively manufactured lattice structures at length scales not previously reported.

Measurement of Mechanical Properties of Friction Stir Welding of Al–Li alloy under different environmental conditions

Measurement of Mechanical Properties of Friction Stir Welding of Al–Li alloy under different environmental conditions

Synthesis and Characterization of All-Acrylic Tetrablock Copolymer Nanoparticles: Waterborne Thermoplastic Elastomers via One-Pot RAFT Aqueous Emulsion Polymerization.

Reversible addition-fragmentation chain transfer (RAFT) aqueous emulsion polymerization is used to prepare well-defined ABCB tetrablock copolymer nanoparticles via sequential monomer addition at 30 °C. The A block comprises water-soluble poly(2-(N-acryloyloxy)ethyl pyrrolidone) (PNAEP), while the B and C blocks comprise poly(t-butyl acrylate) (PtBA) and poly(n-butyl acrylate) (PnBA), respectively. High conversions are achieved at each stage, and the final sterically stabilized spherical nanoparticles can be obtained at 20% w/w solids at pH 3 and at up to 40% w/w solids at pH 7. A relatively long PnBA block is targeted to ensure that the final tetrablock copolymer nanoparticles form highly transparent films on drying such aqueous dispersions at ambient temperature. The kinetics of polymerization and particle growth are studied using 1H nuclear magnetic resonance spectroscopy, dynamic light scattering, and transmission electron microscopy, while gel permeation chromatography analysis confirmed a high blocking efficiency for each stage of the polymerization. Differential scanning calorimetry and small-angle X-ray scattering studies confirm microphase separation between the hard PtBA and soft PnBA blocks, and preliminary mechanical property measurements indicate that such tetrablock copolymer films exhibit promising thermoplastic elastomeric behavior. Finally, it is emphasized that targeting an overall degree of polymerization of more than 1000 for such tetrablock copolymers mitigates the cost, color, and malodor conferred by the RAFT agent.

Use of carboxymethyl cellulose, Klucel G, gum Arabic and zinc oxide nanoparticles nanocomposite as strength agents for inked papyrus

Purpose The purpose of this study is to detect the effect of some natural cellulosic polymers in their nano forms with the addition of zinc oxide nanoparticles on restoring the lost mechanical strength of degraded papyrus without any harmful effects on the inks. Design/methodology/approach In the current study, the USB digital microscopy, scanning electron microscope, measurement of mechanical properties (tensile and elongation), pH measurement, color change and infrared spectroscopy were undertaken for the samples before and after treatment and aging. Findings In the current study, the USB digital microscopy, scanning electron microscope, measurement of mechanical properties (tensile and elongation), pH measurement, color change and infrared spectroscopy were undertaken for the samples before and after treatment and aging. Originality/value The effect of strengthening materials was studied on cellulose and carbon ink, which makes this study closer to reality as the manuscript is the consistent structure of cellulose and inks, whereas most of the literature stated the impact of consolidation materials on the strengthening the cellulosic supports without attention to their impact on inks.

Accurate measurement of mechanical properties of soft materials by introducing transition layers into test samples

Soft materials loaded by conventional clamps are susceptible to damage caused by local stress concentrations, which leads to inaccurate measurement of strength, toughness, and other important properties. Herein, we propose a facile approach to solve the problem by introducing transition layers to test samples. The effectiveness of the proposed method is demonstrated by experiments and numerical analyses. It is found that the introduction of transition layers can stably and accurately reveal the stress-stretch relationship of soft materials by using the conventional hard clamps. What is more, the transition layers have almost no effect on the fracture toughness measurement for pure soft material samples and those with transition layers. These results should be of great significance for the measurement of various materials, and can serve as a design guidance of various soft material structures in blooming applications.

Correction of substrate-induced thin-film modulus deviations in nanoindentation measurements

The influence of substrate effects on the accurate measurement of mechanical properties of thin films remains to be clarified. Therefore, in this study, (AlCrNbSiTi)N thin films were deposited on four substrates—Si, SiO2, sapphire (Al2O3), and Ni—with varying thicknesses. Nanoindentation testing was conducted to measure the mechanical properties, revealing variations in the modulus of the thin film depending on the substrate and film thickness. To address these variations, we introduced the concept of two springs connected in series, following Hooke's law, to determine the elastic deformations of the thin film and its underlying substrate. By applying linear regression to four datasets corresponding to equivalent film thicknesses but different substrates, substrate-induced measurement errors were effectively mitigated, and the true modulus of the thin film was determined. Furthermore, we introduced a k value to represent the ratio of the actual force on the substrate to the force exerted by the indenter. Our findings indicate that even when the indenter contact depth is less than 1% of the film thickness, the substrate is still subjected to 7.6% of the applied force. This underscores the non-negligible nature of substrate elastic deformation during the measurement process and importance of correcting for substrate-induced variations in thin-film moduli. The findings can contribute to advancing the understanding of mechanical properties in ceramics and related materials.

Probe-free optical chromatin deformation and measurement of differential mechanical properties in the nucleus.

The nucleus is highly organized to facilitate coordinated gene transcription. Measuring the rheological properties of the nucleus and its sub-compartments will be crucial to understand the principles underlying nuclear organization. Here, we show that strongly localized temperature gradients (approaching 1°C/µm) can lead to substantial intra-nuclear chromatin displacements (>1 µm), while nuclear area and lamina shape remain unaffected. Using particle image velocimetry (PIV), intra-nuclear displacement fields can be calculated and converted into spatio-temporally resolved maps of various strain components. Using this approach, we show that chromatin displacements are highly reversible, indicating that elastic contributions are dominant in maintaining nuclear organization on the time scale of seconds. In genetically inverted nuclei, centrally compacted heterochromatin displays high resistance to deformation, giving a rigid, solid-like appearance. Correlating spatially resolved strain maps with fluorescent reporters in conventional interphase nuclei reveals that various nuclear compartments possess distinct mechanical identities. Surprisingly, both densely and loosely packed chromatin showed high resistance to deformation, compared to medium dense chromatin. Equally, nucleoli display particularly high resistance and strong local anchoring to heterochromatin. Our results establish how localized temperature gradients can be used to drive nuclear compartments out of mechanical equilibrium to obtain spatial maps of their material responses.

Mechanical behaviour and microstructure of methane hydrate-bearing sandy sediment observed at various spatial scales

Methane hydrates (MHs) are considered an alternative energy resource but also a potential source of geo-hazards and climate change. The physical/mechanical properties of gas hydrate-bearing sandy sediments are strongly dependent on the distribution of hydrates within the pore space. The purpose of this study is to investigate morphologies and pore-habits of MHs formed in sandy sediments by means of experiments that probe a wide range of scales, from the pore scale – using Synchrotron X-Ray Computed Tomography (SXRCT) and optical microscopy – to the core scale, through mechanical property measurements. The same synthetic sands are used, in which MHs are generated successively under excess gas and excess water conditions. At the macroscopic (core) scale, MH pore habits are inferred by comparing the measured sonic wave velocities to velocities calculated from rock physics models and further assessed via triaxial compression tests. Furthermore, Magnetic Resonance Imaging is used to investigate the kinetics of MH formation and distribution along the core height. The pore habits and MH morphologies are directly visualized at the pore (grain) scale by SXRCT and, with still better spatial and temporal resolution, by transmission optical microscopy, revealing some more complex morphologies than in the hydrate pore habits commonly admitted.

Measurement and analysis mechanical properties of cross-laminated timber (CLT) product: Case study on typical lampung lamina arrangement

Recently, the development of cross-laminated timber (CLT) products that can substitute large-dimensional wood for structures and reduce waste of wood products with small dimensions and pieces continues to be developed, and demand from industries continues to increase. Therefore, this study aims to measure and analyze the mechanical properties of cross-laminated timber (CLT) products designed with a typical arrangement of the Lampung region, Indonesia, called a screen arrangement. Measurement and analysis of mechanical properties include measuring load tests and analyzing moments and stiffness of CLT products intended for floor and beam structures. The screen-type wood arrangement used in the product consists of an inner screen arrangement, an outer screen arrangement, and a standing screen arrangement with polyvinyl acetate adhesive. Load test measurements were carried out using a universal testing machine (UTM) and moment and bending stress analysis using engineering mechanics. Generally, the results show that CLT products with standing screens have smaller mechanical properties than those intended for floors and beams. This research shows that the typical CLT arrangement of the Lampung region (Indonesia), in the form of a screen, has strong mechanical properties and characteristics that can be compared with other arrangements.

High-throughput single-cell assay for precise measurement of the intrinsic mechanical properties and shape characteristics of red blood cells.

The intrinsic physical and mechanical properties of red blood cells (RBCs), including their geometric and rheological characteristics, can undergo changes in various circulatory and metabolic diseases. However, clinical diagnosis using RBC biophysical phenotypes remains impractical due to the unique biconcave shape, remarkable deformability, and high heterogeneity within different subpopulations. Here, we combine the hydrodynamic mechanisms of fluid-cell interactions in micro circular tubes with a machine learning method to develop a relatively high-throughput microfluidic technology that can accurately measure the shear modulus of the membrane, viscosity, surface area, and volume of individual RBCs. The present method can detect the subtle changes of mechanical properties in various RBC components at continuum scales in response to different doses of cytoskeletal drugs. We also investigate the correlation between glycosylated hemoglobin and RBC mechanical properties. Our study develops a methodology that combines microfluidic technology and machine learning to explore the material properties of cells based on fluid-cell interactions. This approach holds promise in offering novel label-free single-cell-assay-based biophysical markers for RBCs, thereby enhancing the potential for more robust disease diagnosis.